Complete Weldless Fitting Sets
$5.00 Flat rate shipping to US 50 states
We ship to Canada
click for details. ORDER PARTS HERE
Step Bit available on the parts page.
KEG - KETTLE - POT
CONVERSION KIT   |
COPPER
PICK UP / DIP TUBE  Straight pick up tube. 11" long  Side pick up tube  Center pick up tube |
STAINLESS STEEL PICK UP / DIP
TUBE    INSTALLATION HOWTO |
| For keg and cooler walls up
to
1/8" thick Convert your keg, kettle, pot or thin wall cooler. This bulkhead is made of all stainless parts and silicone o-rings. All parts are 1/2" NPT (pipe threads) Purchase as a bulk head only or add a stainless or brass valve and hose barb to complete the set. Coupling inside allows you to add a dip tube or strainer sold separately on this page. Hose barbs fit 1/2" Inner diameter tubing Requires a 13/16" step bit or hole saw to install. INSTALLATION INSTRUCTION FOR KEG Welded Option - Choose this only if you are going to weld in your fitting set! |
1/2"
OD copper tube. 1/2" NPT male thread fits weldless conversion
kits sold on this page. Fully soldered
connection. Lead free silver bearing solder and Plumbing safe
fluxes are used to create these dip / pickup tubes. Available
in 11" straight, side pickup and Center pickup.
Easily bent and cut to modify to your exact needs. DESIGNED FOR WELDLESS KITS ONLY |
DESIGNED TO FIT A SANKEY STYLE KEG Available with or without 1/2 NPT x 1/2 OD compression fitting, When you purchase the fitting you receive the ss tube ferrules that will allow a rigid installation and 2 o-rings to allow the tube to be installed and still be removed for cleaning. Weldless set shown sold separately. Please specify if your keg has a welded coupling or a weldless coupling installed. This will determine the length of the ss drain tube. The welded option assumes the coupling is welded half way through the keg. If you have it flush email info to be sure the diptube lands in the center of the keg. |
COOLER WELDLESS CONVERSION
FITTING KIT |
SIGHT GAUGE FOR KETTLE OR KEG  |
THERMOMETER
SIGHT GAUGE KETTLE KEG OR COOLER 
Thermometer is optional below! |
| This
bulkhead is made of all stainless parts and silicone
o-rings.
Purchase as a bulk head only or add a stainless or
brass valve and
hose barb to complete the set. Coupling inside allows you to
add a
dip tube or strainer sold separately on this page.
All parts are
1/2" NPT (pipe threads) Hose barbs fit 1/2" Inner
diameter tubing Requires a 13/16" step bit or hole saw to install. INSTALL INSTRUCTION FOR COOLER STANDARD COOLER Walls from 3/16" - 5/8" thick THICK WALL COOLERS 11/16" and larger |
Weldless
sight gauge for your keg, hot liquor tank kettle, brew pot and
coolers. 1/2" NPT pipe thread
connections. .
Stainless fittings. Stainless eye bolt to stabilize
at top of
the kettle. High temp poloycarbonate sight tube. Requires a 13/16" step bit or hole saw to install. INSTALLATION INSTRUCTIONS |
Weldless
thermometer sight gauge for your hot liquor tank, brewpot or cooler.
1/2" NPT
pipe thread connections. Stainless fittings. Stainless eye
bolt to stabilize at top of the kettle.
High
temp poloycarbonate sight tube.
No calibration screw on
thermometer. See listing below for thermometer details. 4" stem will project 1.5" in using the keg fitting 6" stem will be 2.5" into the vessel. Long nipples will require the 6" stem. Thermometer face may vary. Some may only be in Fahrenheit Requires a 13/16" step bit or hole saw to install. INSTALLATION INSTRUCTION FOR KEG INSTALL INSTRUCTION FOR COOLER |
LOCKNUT
FOR ELECTRIC HEATER ELEMENT |
STAINLESS
STEEL MASH BRAID  |
WELDLESS THERMOMETER - 1/2"
BACK THREAD |
| Comes
with one
silicone o-ring and one 1 inch NPT locknut. This is a straight thread fitting. It will allow you to tighten it hand tight and get a leak free connection. Nut has a groove for the o-ring to keep it seated when you tighten it down Can be used in kegs and kettles and thin wall coolers. You will need a 1.25" drill bit to install a water heater element. Separate parts available on the parts page. |
316
Stainless 1/2" male thread X 1/2" hose barb fitting, 100%
stainless steel hose clamp. 10" long stainless steel mesh
braid. Available with or without the hose barb. Use this in your converted kettle, cooler or keg. Best used with the batch sparge method when mashing grain. Can be used with whole hops in the boil kettle but is prone to clogging if used with an immersion chiller due to the cold break material. Will not work with pellet hops / immersion chiller in boil kettle. |
3 inch face -
Available with 2.5, 4 or 6 inch probe. Specifications: Dial Size: 3" Case, Stem: 304 Stainless Steel Connection: 1/2" NPT. Accuracy: 1% of full scale Dual Scale - Fahrenheit No calibration screw Requires a 13/16" step bit or hole saw to install. hermometer face may vary. Some may only be in Fahrenheit If you need the faces to match email me to be sure. I'm working with my vendor to get consistent faces on these. "Weldless adapter ONLY" includes - 1/2" Stainless locknut, 2 silicone orings and 1 stainless shim washer. |